Friday, December 2, 2011

Binding Tutorial

The first time I put binding on a quilt it looked horrible in my opinion. I was so intimidated and not really sure of what I was doing at all. I think I got it now, finally. In the process of making binding today, I took some pictures to explain the process and also to have "notes" for myself. This blog isn't just to meet new quilters but to also keep a journal that I can enjoy and reference in the future. This is how I make my binding.

You can also check out wonderful tutorials I linked to my blog under My Favorite Tutorials on the lower right side of my blog.

Now...lets get down to binding...

 Measure all sides of your quilt. Add 12.

Lets use this picture as an example:
45+45+60+60+12=222 inches

Divide 222 by 40 (222/40) = 5.55   Round 5.55 to 6 (this is the number of strips you need to cut)

(The reason we're dividing it by 40 is because it's assuming you're using a yard cut of fabric that measures 42 to 44 inches in width, with an extra few inches to spare)

 I like cutting my strips 2.25 inches. For this example I will be cutting (6) 2.25in x 40 strips.

Side note:
 1.You don't necessarily need to have a entire yard to make binding strips. If you're binding a smaller quilt, lets say measuring 36 x 45. You would only need about 5 strips and a piece of fabric measuring 12x42 inches,would be just enough.
2. If you are making a multi colored binding or using a different size cut of fabric. just make sure after the strips sets are sewed together they reach your total amount. Example: 222inches

Now place 2 strips right sides together at a 90 degree angle.

I fold the top right corner of the top strip to make a 45 degree angle and crease.

I like to mark the crease and pin.

Sew along the line and trim to 1/4 inches and press open seams (to avoid bulk).

You should have a nice diagonal seam, when you turn the strips to the right side. Continue to sew all of the strips together following the steps above.

Next folds the strips in half (wrong sides together) and iron.

All done!! Now lets get it on the quilt.

While using your walking foot, stitch 1/4 inch from the edge of your quilt.  Do not start sewing the binding on at a corner. Star in the middle of one of the longer sides of your quilt leaving about a 6" tail of binding.

When you reach  1/4"  of an inch from the bottom of your quilt, stop. Pivot needle and sew a 90 degree angle (see picture below)

Then fold binding  up at a 45 degree angle, fold it down over the angle and from 1/4" from the top continue sewing 1/4" from the edge of the quilt (see pictures below).

Continue these steps with all 4 corners.

Your corners should look like this. :)

When you're done it should look something like this.

Overlap your binding tails. Important step: Have your tails over lap the width of your binding strip (2.25) plus (+) .25 in. = 2.50" (2 1/2") in.

Open up the binding and place strips right sides together (this can be a little difficult). Looking at the picture below you can see I pinned it in place leaving about 1/8" at both ends of the strips.

I drew a diagonal line and stitched along the line, trimed to 1/4" and pressed open.  

And magically it's the correct length! Just continue stitching the binding down.


I then iron the binding flat, fold the binding over and iron again. I feel it helps keep the binding flat. Pin and hand stich the binding to the back of the quilt.

All done! Yay!

Here's mine...all pined and ready to be hand sewn to the back. Hand sewing it can take some time, but i like the clean look it gives.

I hope this tutorial was clear and understandable. This is my first tutorial that i've posted and i hope it can help someone out there. 

Happy quilting...and binding! :)

Thursday, December 1, 2011

Time to quilt it...

It's been a while since I've wrote. A lot of good things have been keeping me busy the last few months.

A few months ago I was lucky enough to attend a machine quilting feathers class at my local quilt shop. The world renowned Mark Sherman was the instructor! I had a blast and learned some great techniques. The most important tip was practice, practice, and, more practice. I need to get these quilt tops quilted!
Here's the sample I quilted in class:

From time to time I'll post some of my practice pieces so I can see my growth.

Happy quilting!
(I'm posting from my phone in hopes of posting much more frequently) :)

Friday, August 12, 2011

Finally a finish...

I have so many UFO's to finish, but i really wanted to finally complete this one. I started it almost 2 years ago.
On to the next....after I machine quilt this one.

Tuesday, July 26, 2011

Machine Quilting

Today i gave machine quilting a try. I have quilt tops that are in desperate need of being quilted. I have a long way to go...practice, practice, practice!
The front:
The back:

Wednesday, July 20, 2011

I'm back!

I haven’t written in a LONG time. I’m happy to be back and I’m going to make an attempt to write on a regular basis.

A couple of months ago I received the best birthday gift ever...
My Bernina 44QE! I waited forever for it and I couldn’t be more pleased to have it. Since buying it I haven’t been able to “play” with it since we (my soon to be hubby and I) relocated to another State right after it was purchased. I’m not quite settled in yet, but I always have time to quilt! Now i can learn to machine quilt! Yay! I’ll be writing about my experiences as I learn to use my Bernina, as i try out new quilting techniques, and to simply have fun. Another purpose of this blog is to also meet other quilters and hopefully get inspired and learn something new.


Related Posts Plugin for WordPress, Blogger...